File Name: 1-1C8KPE.ps File Size: 10.45 MB Date Posted: 9/6/2011 Date Published: 1/3/2012 Criticality: Recommended Description: Composite patch for Xerox Integrated Fiery Color Server For the Xerox 700 Digital Color Press ID: 1-1C8KPE Installation Order: 2 Notes: Before installing 1-1C8KPE.ps 1. This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. The following prerequisite(s) must be installed in the order specified before applying the 1-1C8KPE.ps patch: None.

Known issues listed below, read before installing 1-1C8KPE.ps patch: None. Patch installation instruction 1. Make sure that the Fiery is Idle. Import the patch file 1-1C8KPE.ps using Command Workstation to the Direct queue. You must wait until the file finishes processing and CWS or LCD show Idle. This ensures the patch file is completely processed. User should wait two minutes for complete installation of patch.

From Command WorkStation, choose Server- Reboot Server, or from the Fiery LCD, select Shut down - Reboot System. Wait until the Fiery comes to Idle and print the configuration page.

Verify that the System Update Log contains the patch number 1-1C8KPE.ps. Requires exclusive install 7854 Download. File Name: Integrated700i1.0SP1.ps File Size: 3.85 MB Date Posted: 3/29/2012 Date Published: 4/10/2012 Criticality: Recommended Description: Service Pack 1 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP1 Installation Order: 3 Notes: Before installing Integrated700i1.0SP1 1.

Known issues listed below, read before installing Integrated700i1.0SP1 patch: This patch contains the Fast Black enabler. Use the following settings to enable the feature: a. In WebTools: Select Configure-PDL-PS called Enable black 2. When set to On, it will enable the engine to print b/w pages using black ink only. It will continue to do black-only mode until a color page is received. Once in color mode it can't switch to black-only mode (even if b/w page is received) until the engine cycles down.

The following prerequisite(s) must be installed in the order specified before applying the Integrated700i1.0SP1 patch: 1-1C8KPE 2. This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1. Make sure that the Fiery is Idle. Import the patch file Integrated700i1.0SP1 using Command Workstation to the Direct queue.

You must wait until the file finishes processing and CWS or LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. Wait until the Fiery comes to Idle and print the configuration page. Verify that the System Update Log contains the patch number SP1. Requires exclusive install 8669 Required Software: Download.

File Name: Integrated700i1.0SP2.ps File Size: 337.96 KB Date Posted: 7/15/2012 Date Published: 8/14/2012 Criticality: Recommended Description: Service Pack 2 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP2 Installation Order: 5 Notes: Before installing SP2.ps 1. Known issues listed below, read before installing SP2.ps patch: None.

The following prerequisite(s) must be installed in the order specified before applying the SP2.ps patch: 1-1C8KPE SP1 3. Do NOT install any of the following patch(es) after installing the SP2.ps patch. If you must install any of the patch(es) below, do so before installing the SP2.ps patch: None.

This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1.

Make sure that the Fiery controller has reached Idle. Import the patch file SP2.ps using Command WorkStation to the Direct connection.

You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. From Command WorkStation, choose Server-Reboot Server, or from the Fiery LCD, select Shut down-Reboot System.

Wait until the Fiery controller reaches Idle and print the configuration page. Verify that the System Update Log contains the patch number SP2.

Requires exclusive install 9306 Required Software:, Download. File Name: Integrated700i1.0SP3.ps File Size: 1.49 MB Date Posted: 10/5/2012 Date Published: Criticality: Recommended Description: Service Pack 3 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP3 Installation Order: 6 Notes: Before installing SP3.ps 1 Known issues listed below, read before installing SP3.ps patch: None. 2 The following prerequisite(s) must be installed in the order specified before applying the SP3.ps patch: 1-1C8KPE SP1 SP2 3 Do NOT install any of the following patch(es) after installing the SP3.ps patch.

If you must install any of the patch(es) below, do so before installing the SP3.ps patch: None. 4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once.

After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle.

We don't know all the spamtrap email addresses, but we do know a lot of them. We have technology in place to determine if certain emails should be classifed as spamtrap. Best email crawlers and bulk senders for mac. We recommend not emailing these addreesses. Abuse - These emails are of people who are known to click the abuse links in emails, hence abusers or complainers.

2 Import the patch file SP3.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number SP3.

Requires exclusive install 9710 Required Software:, Download. File Name: Integrated700i1.0SP4.ps File Size: 11.48 MB Date Posted: 12/6/2012 Date Published: 1/10/2013 Criticality: Recommended Description: Service Pack 4 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP4 Installation Order: 7 Notes: Before installing SP4.ps 1 Known issues listed below, read before installing SP4.ps patch: None. 2 The following prerequisite(s) must be installed in the order specified before applying the SP4.ps patch: 1-1C8KPE SP1 SP2 SP3 3 Do NOT install any of the following patch(es) after installing the SP4.ps patch.

If you must install any of the patch(es) below, do so before installing the SP4.ps patch: None. 4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server.

Patch installation instruction 1 Make sure that the Fiery controller has reached Idle. 2 Import the patch file SP4.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System.

5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number SP4. Requires exclusive install 10059 Required Software:, Download. File Name: 1-1IFBLL.ps File Size: 488.57 KB Date Posted: Date Published: 1/11/2013 Criticality: Recommended Description: FreeFlow 9.0 SP8 Enablement patch for Fiery Xerox Integrated 700i v1.0.

ID: 1-1IFBLL Installation Order: 8 Notes: Before installing 1-1IFBLL.ps 1 Known issues listed below, read before installing 1-1IFBLL.ps patch: System Specifed Option is not functioning from JobSetup-Output Order. Tab text cut off issue is releated to engine issue. Dierct Insert is not supported from Freeflow for Xerox Integrated Fiery for Xerox 700i v1.0 2 The following prerequisite(s) must be installed in the order specified before applying the 1-1IFBLL.ps patch: 1-1C8KPE SP1 1-1DHYNF SP2 SP3 3 Do NOT install any of the following patch(es) after installing the 1-1IFBLL.ps patch. If you must install any of the patch(es) below, do so before installing the 1-1IFBLL.ps patch: None. 4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle.

Xerox Dcp 700 Drivers For Mac Pro

2 Import the patch file 1-1IFBLL.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System.

5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number 1-1IFBLL. Requires exclusive install 10153 Required Software:, Download. File Name: Integrated700i1.0SP5.ps File Size: 4.80 MB Date Posted: 1/29/2013 Date Published: 3/21/2013 Criticality: Recommended Description: Service Pack 5 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP5 Installation Order: 9 Notes: Before installing SP5.ps 1.Known issues listed below, read before installing SP5.ps patch: None. 2.The following prerequisite(s) must be installed in the order specified before applying the SP5.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 3.Do NOT install any of the following patch(es) after installing the SP5.ps patch. If you must install any of the patch(es) below, do so before installing the SP5.ps patch: None.

4.This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1.Make sure that the Fiery controller has reached Idle.

2.Import the patch file SP5.ps using Command WorkStation to the Direct connection. 3.You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed.

User should wait one minute for complete installation of patch. 4.From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5.Wait until the Fiery controller reaches Idle and print the configuration page. 6.Verify that the System Update Log contains the patch number SP5. Requires exclusive install 10285 Required Software:, Download.

File Name: Integrated700i1.0SP6.ps File Size: 2.30 MB Date Posted: 4/29/2013 Date Published: 5/14/2013 Criticality: Recommended Description: Service Pack 6 for Xerox Integrated Fiery for Xerox 700i v1.0. ID: SP6 Installation Order: 10 Notes: Before installing SP6.ps 1 Known issues listed below, read before installing SP6.ps patch: This patch will obsolete 1-1J8FGI, 1-1IQ5HP, 1-1IZWYI and 1-1H0SGZ patches. 2 The following prerequisite(s) must be installed in the order specified before applying the SP6.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 3 Do NOT install any of the following patch(es) after installing the SP6.ps patch. If you must install any of the patch(es) below, do so before installing the SP6.ps patch: None. 4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle.

2 Import the patch file SP6.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System.

5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number SP6. Requires exclusive install 10711 Required Software:, Download.

File Name: 1-1K42SH.ps File Size: 3.29 MB Date Posted: 7/1/2013 Date Published: 8/9/2013 Criticality: Recommended Description: Unable to print Tabstock for particular jobs from FreeFlow. ID: 1-1K42SH Installation Order: 11 Notes: Before installing 1-1K42SH.ps 1.Known issues listed below, read before installing 1-1K42SH.ps patch: This patch is obsolete with the patch 1-1JZA7A. Before printing a tab job, always check to see if all the banks are full tab banks. If the tray containing tab stock is opened for any reason, the printer will always assume that the ordered sequence is correct and/or reset. Always check to see for full tab banks in the tray when the tray is opened.

Always select a specific output destination for tab kick out and avoid using Auto Select and Document Default. For tab jobs created using Define Page Range and Tab Shift, partially used tab sets are not automatically ejected at the end of the print run. When Offset is ON, after clearing a paper jam condition, the ejected unfinished job will be offset with the remaining part of the incoming job. This behavior is expected as the printer always ejects the unfinished job to the sorter tray. Cancelling a tab job after an engine fault mid-stream will result in ordered tab stock out of sequence. Manual re-ordering of tab stock in the tray is required if a tab job is cancelled during a print run.

2.The following prerequisite(s) must be installed in the order specified before applying the 1-1K42SH.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 SP6 3.Do NOT install any of the following patch(es) after installing the 1-1K42SH.ps patch. If you must install any of the patch(es) below, do so before installing the 1-1K42SH.ps patch: None. 4.This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1.Make sure that the Fiery controller has reached Idle. 2.Import the patch file 1-1K42SH.ps using Command WorkStation to the Direct connection. 3.You must wait until the file finishes processing and Command WorkStation or the LCD show Idle.

This ensures the patch file is complet Requires exclusive install 10940 Required Software:, Download. File Name: Integrated700i1.0SP7.ps File Size: 8.25 MB Date Posted: Date Published: 11/5/2013 Criticality: Recommended Description: Service Pack 7 for Xerox Integrated Fiery for Xerox 700i v1.0 ID: SP7 Installation Order: 12 Notes: Before installing SP7.ps 1 Known issues listed below, read before installing SP7.ps patch: This patch will obsolete 1-1KCI4P. 2 The following prerequisite(s) must be installed in the order specified before applying the SP7.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 SP6 3 Do NOT install any of the following patch(es) after installing the SP7.ps patch. If you must install any of the patch(es) below, do so before installing the SP7.ps patch: None.

4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle. 2 Import the patch file SP7.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle.

This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5 Wait until the Fiery controller reaches Idle and print the configuration page.

6 Verify that the System Update Log contains the patch number SP7. Requires exclusive install 11468 Required Software:, Download. File Name: FIT191856.ps File Size: 3.93 MB Date Posted: 1/20/2014 Date Published: 4/27/2014 Criticality: Recommended Description: iOS7 compatibility reference patch for Xerox Linux products. Xerox Integrated Fiery for the Xerox 700i Xerox 550-560 Integrated Fiery Xerox WorkCentre7800Series(EFI) Xerox EXi 570 Print Server Powered by Fiery Xerox Integrated Fiery Color Server, for the Xerox C75 Press ID: FIT191856 Installation Order: 13 Notes: Patch installation instructions 1 Make sure that the Fiery controller has reached Idle. 2 Import the patch file FIT191856.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle.

This ensures the patch file is completely processed. User should wait 2 minutes for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Updates Log contains the patch number FIT191856. Requires exclusive install 11801 Download. File Name: FIT204730.ps File Size: 2.74 MB Date Posted: 4/7/2014 Date Published: 4/7/2014 Criticality: Recommended Description: Patch to address incompatibility issue between the Configure application and JRE 1.7u51.

ID: FIT204730 Installation Order: 14 Notes: Before installing FIT204730.ps 1. Please refer to the patch Addendum for additional information regarding this release. Known issues listed below, read before installing FIT204730.ps patch: None.

The following prerequisites must be installed in the order specified before the FIT204730.ps patch is installed: 1-1C8KPE.ps SP1 SP2 SP3 SP4 SP5 SP6 SP7 4. Do NOT install any of the following patch(es) after installing the FIT204730.ps patch. If you must install any of the patch(es) below, do so before installing the FIT204730.ps patch: None. This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. In the case where the customer needs to install a patch which was previously skipped in the patch order, it is necessary to reinstall the system. Patch installation instructions Please refer the Release Notes for 'Patch installation instructions'.

Requires exclusive install 12162 Required Software:, Download. File Name: FIT156350.ps File Size: 3.02 MB Date Posted: 4/14/2014 Date Published: 4/23/2014 Criticality: Recommended Description: Fiery patch to address Gradation issue. ID: FIT156350 Installation Order: 15 Notes: Before installing FIT156350.ps 1.Known issues listed below, read before installing FIT156350.ps patch: Perform ES-1000/ES-2000 calibration before and after the patch. While performing calibration on large paper size (11x17,A3, 12x18) use 34 Sorted Patches options. 2.The following prerequisite(s) must be installed in the order specified before applying the FIT156350.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 SP6 SP7 3.Do NOT install any of the following patch(es) after installing the FIT156350.ps patch.

If you must install any of the patch(es) below, do so before installing the FIT156350.ps patch: None. 4.This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once.

After that, other patches can be applied to the server. Patch installation instruction 1.Make sure that the Fiery controller has reached Idle. 2.Import the patch file FIT156350.ps using Command WorkStation to the Direct connection.

3.You must wait until the file finishes processing and Command WorkStation or the LCD show Idle. This ensures the patch file is completely processed.

User should wait one minute for complete installation of patch. 4.From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5.Wait until the Fiery controller reaches Idle and print the configuration page. 6.Verify that the System Update Log contains the patch number FIT156350. Requires exclusive install 12196 Required Software:, Download.

File Name: FIT221317.ps File Size: 1.31 MB Date Posted: 7/24/2014 Date Published: 9/5/2014 Criticality: Recommended Description: Fiery patch to address trim issues. ID: FIT221317 Installation Order: 16 Notes: Before installing FIT221317.ps 1 Known issues listed below, read before installing FIT221317.ps patch: None. 2 The following prerequisite(s) must be installed in the order specified before applying the FIT221317.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 SP6 SP7 3 Do NOT install any of the following patch(es) after installing the FIT221317.ps patch. If you must install any of the patch(es) below, do so before installing the FIT221317.ps patch: None.

4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle. 2 Import the patch file FIT221317.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle.

This ensures the patch file is completely processed. User should wait one minute for complete installation of patch.

4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number FIT221317. Requires exclusive install 12696 Required Software:, Download.

File Name: FIT217064.ps File Size: 1.40 MB Date Posted: 8/11/2014 Date Published: 9/8/2014 Criticality: Recommended Description: Fiery Patch to support PCL driver. ID: FIT217064 Installation Order: 17 Notes: Before installing FIT217064.ps 1 Known issues listed below, read before installing FIT217064.ps patch: None. 2 The following prerequisite(s) must be installed in the order specified before applying the FIT217064.ps patch: 1-1C8KPE SP1 SP2 SP3 SP4 SP5 SP6 SP7 3 Do NOT install any of the following patch(es) after installing the FIT217064.ps patch. If you must install any of the patch(es) below, do so before installing the FIT217064.ps patch: None.

4 This patch is exclusive, it must be installed by itself, and the server must be rebooted or restarted once. After that, other patches can be applied to the server. Patch installation instruction 1 Make sure that the Fiery controller has reached Idle. 2 Import the patch file FIT217064.ps using Command WorkStation to the Direct connection. 3 You must wait until the file finishes processing and Command WorkStation or the LCD show Idle.

This ensures the patch file is completely processed. User should wait one minute for complete installation of patch. 4 From Command WorkStation, choose Server, Reboot Server, or from the Fiery LCD, select Shut down, Reboot System. 5 Wait until the Fiery controller reaches Idle and print the configuration page. 6 Verify that the System Update Log contains the patch number FIT217064. Requires exclusive install 12740 Required Software:, Download.

Xerox 700 Digital Color Press is a professional and commercial photo printer, combining their digital imaging and digital printing skills to take advantage of the growing market for speciality photo products. Xerox 700 Digital Color Press uses low melt emulsion aggregate (EA) aggregates made by Xerox and FujiXerox, producing full-color prints at high speeds. Micro-toner particles also ensure high-quality halftones, smooth transitions, and rich shadow detail. This environmentally friendly toner requires less energy to produce and print, minimizing the impact on the environment. Xerox 700 produces quality photo output that meets the high standards of our pro and commercial lab customers, 'said Thomas Curley, director of marketing, Imaging Division, Fujifilm USA, Inc.' With this solution, Fujifilm helps our customers grow. Revenue and expand their product offerings.

Printable items include photo books, photo calendars, greeting cards, and trading cards, exciting packages and a host of other specially printed photo products. Xerox 700 Digital Color Press can print a variety of photo book sizes that add to the range of commercial and professional photo lab products that can offer their customers.

Fujifilm and Xerox have collaborated to create custom-sized photo paper for Xerox 700 to support the fulfilment of speciality photo products. Features Xerox 700 Digital Color Press can print at speeds up to 70 ppm in color and monochrome. This printer prints with impressive image quality at 2400 x 2400 and prints up to 13 'x 19.2' maximum sheet size. The printer is also capable of printing on various substrates, up to 110 lb cover / 300 g / m2 and automatic two-sided printing up to 80 lb / 220 g / m2 cover.

Xerox 700 Digital Color Press uses low melt emulsion aggregate (EA) aggregates made by Xerox and FujiXerox, producing full-color prints at high speeds. In addition to the Xerox 700 Digital Color press, Fujifilm will feature Xerox DocuColor 242/252/260 which offers professional and commercial labs of high-resolution in-store printing solutions for special photo products. Refreerences: Xerox 700 Digital Color Press Driver Supports for Os: Android / Mobile Windows 10 Windows 8 Windows 7 Windows XP Windows Vista Mac Os X Linux Xerox Driver Installation Step by Step.